Products · WSP80-compatible · LHT
LHT tips: more metal, more heat, same seat.
LHT is the high-power end of the WSP family. The tips carry more metal and wider faces for lugs, ground planes and connector shells, on the same push-fit principle as the WSP80.
- Platform
- LHTWSP150 / 151
- Station class
- high power150 W class
- Face range
- 2–8 mm classwide chisel
- Minimum order
- 20 pcsper geometry
What it is
A wide face needs a body that can feed it.
A wide chisel is only useful if the body behind it can carry enough heat. LHT tips are heavier for that reason: the extra metal stores energy and feeds the face during the joint, instead of letting the face cool as soon as it touches a lug.
The seat is still a push fit, but the shank is larger and the insertion depth differs from the WSP80. A WSP80 tip will not fit an LHT iron, and an LHT tip will not fit a WSP80 sleeve. Confirm the iron before ordering.
Published geometries
LHT codes, faces and typical joints.
Face width is quoted as the class for that code. The exact A/B/C/D dimensions for a specific part number are issued with the quotation, not estimated on the page.
| Code | Face | Working width | Typical joint |
|---|---|---|---|
| LHT-B | Conical | 1 mm class | General pads |
| LHT-D | Chisel | 3.2 mm class | Lugs and shields |
| LHT-K | Screwdriver | 4 mm class | Connector rows |
| LHT-LI | Bent chisel | 2 mm class | Recessed joints |
| LHT-DV | Wide chisel | 6–8 mm class | Ground planes |
Codes are listed by face family. Variants with a different width, bend or reach are ground to order; send the drawing or the joint photograph and we will confirm the code.
Compatibility
What it fits — and what to check.
| Machine or holder | Interface | Note |
|---|---|---|
| WSP150 iron | LHT shank | Direct fit |
| WSP151 iron | LHT shank | Confirm length |
| WSP80 iron | smaller sleeve | Use WSP80 series |
Model names describe the machine a part fits. XANJO replacement parts are independent parts, not original equipment manufacturer parts.
Dimensions
Four numbers define the part.
A is the overall length from the seat to the working face. B is the shank or body diameter. C is the width of the working face. D is the reach from the seat reference to the face — the number that decides whether the part can touch the joint without the housing fouling the board.
We hold ±0.05 mm on the shank and seat, and we issue the drawing revision with every batch. If a dimension is not measured, it does not go on the drawing: that is why some codes are marked “drawing on request” rather than filled with an estimate.
Ordering
Samples, minimums and lead time.
LHT shanks are stocked in the common lengths; wide faces are ground to order.
- Minimum order
- 20 pcsper geometry, mixed codes allowed within a family
- Custom samples
- 5 daysground or machined on the production line
- Stocked codes
- 48 hdispatch after order confirmation
- Batch documents
- Includeddimension report, plating or face report, RoHS 3 declaration
Questions we are asked
LHT fitting and ordering.
Will an LHT tip fit a WSP80 iron?
No. The LHT shank is larger and the insertion depth differs. Use the WSP80 series for a WSP80 or WP80 iron.
What is an LHT tip used for?
Lugs, ground planes, connector shells and other joints with enough thermal mass to cool a small tip. The wide chisel faces are the reason the series exists.
Can you make a custom LHT face?
Yes, to drawing or sample. The shank is standard; the face is ground to order.
Are these OEM parts?
No. XANJO replacement tips are independent parts.
Other WSP80-compatible tips series
If this is not your machine.
Send the part number. We’ll send the drawing.
A code, a machine model or a photograph of the holder is enough. We reply with the geometry, the A/B/C/D drawing and the specification within one working day.