Products · Hand soldering · 200 series
200 series tips for 90 W high-frequency stations.
The 200 series is the tip family for QUICK high-frequency stations: a ring seat, a 90 W heater and a large thermal mass in a short body. It is the family to reach for when the joint is a through-hole pin on a thick board, or a lug that keeps sinking heat.
- Platform
- 200203H / 204H / 2000A / 200K
- Station class
- 90 Whigh frequency
- Geometry families
- 4horseshoe, chisel, conical, bent
- Minimum order
- 20 pcsper geometry
What it is
Built for thermal mass, not for fine pitch.
High-frequency stations recover quickly because the heater is close to the working face, but recovery is only half the problem: a joint with a large copper pour will still pull heat out of a small tip faster than the station can replace it. The 200 series answers that with volume — a horseshoe or a wide chisel that stores solder and heat at the same time.
That is why the family is dominated by 1C, 2C and 4C horseshoes and by 2.4 mm to 4 mm chisels, with conical geometries reserved for the occasional fine pad on the same board.
Published geometries
200 codes, shapes and typical joints.
Face width is quoted as the class range for that code. The exact A/B/C/D dimensions for a specific part number are issued with the quotation, not estimated on the page.
| Code | Geometry | Face width | Typical joint |
|---|---|---|---|
| 200-1C | Horseshoe | 1.0 mm class | Small through-hole pins |
| 200-2C | Horseshoe | 2.0 mm class | General through-hole, connectors |
| 200-4C | Horseshoe | 4.0 mm class | Large pins, heat sinks, shields |
| 200-B / 200-I / 200-J | Conical | 0.5–1.0 mm class | Fine pads on the same board |
| 200-D | Chisel | 2.4–4.0 mm class | Lugs, ground planes, drag soldering |
| 200-K / 200-SK | Knife | 2.0 mm class | Connector rows |
| 200-LI | Bent conical | 0.5–1.0 mm class | Recessed or crowded joints |
Codes are listed by geometry family. Variants with a different bend angle, reach or face width are ground to order; send the drawing or the joint photograph and we will confirm the code.
Compatibility
What it fits — and what to check.
| Iron or station | Handle / interface | Note |
|---|---|---|
| QUICK 203H | 200 series handle | Direct fit |
| QUICK 204H | 200 series handle | Direct fit |
| QUICK 2000A / 200K | 200 series handle | Direct fit |
| Clone stations | 200-compatible collars | Check ring position |
Model names describe the machine a tip fits. XANJO replacement tips are independent parts, not original equipment manufacturer parts.
Dimensions
Four numbers define a tip.
A is the overall length from the seat to the working face. B is the shank or tube diameter. C is the width of the working face. D is the reach from the seat reference to the face — the number that decides whether the tip can touch the joint without the housing fouling the board.
We hold ±0.05 mm on the shank and seat, and we issue the drawing revision with every batch. If a dimension is not measured, it does not go on the drawing: that is why some codes are marked “drawing on request” rather than filled with an estimate.
Ordering
Samples, minimums and lead time.
- Minimum order
- 20 pcsper geometry, mixed codes allowed within a family
- Custom samples
- 5 daysground on the production line
- Stocked codes
- 48 hdispatch after order confirmation
- Batch documents
- Includeddimension report, plating build-up, RoHS 3 declaration
Questions we are asked
200 fitting and ordering.
Why does my 200 series tip lose heat on a big joint?
Usually because the working face is too small for the copper it is heating, not because the station is underpowered. A 1C horseshoe holds far less solder and heat than a 4C on the same collar. Move up one face size before you move the temperature up.
What is the difference between C and D geometry?
C is a horseshoe: a concave face that holds a solder bead and wraps a pin. D is a chisel: a flat face with a defined edge, better for dragging along a row of pads or a lug. On the same joint the horseshoe transfers heat more gently, the chisel more directly.
Do 200 series tips fit 900M irons?
No. The 200 series seats on a ring at the heater collar, while 900M tips are push-fit into the barrel. The two families are not interchangeable.
Are these original manufacturer parts?
No. 200 describes the station interface. XANJO replacement tips are independent parts and are not affiliated with, endorsed by or sponsored by any original equipment manufacturer.
Other hand soldering series
If this is not your iron.
900M
900M series
Straight-barrel push fit with the widest geometry range in the family.
View series →
T18
T18 series
Five core codes dimensioned for the FX-888D and FX-889 housing.
View series →
T12
T12 series
Integrated heater cartridges: fast recovery, sleeve seat, no separate heater.
View series →Send the part number. We’ll send the drawing.
A code, an iron model or a photograph of the socket is enough. We reply with the geometry, the A/B/C/D drawing and the plating specification within one working day.